in standard spherical bearings, the spherical ball is made from iglide® L280 material, which is known for the lowest coefficients of friction in dr...

in standard spherical bearings, the spherical ball is made from iglide® L280 material, which is known for the lowest coefficients of friction in dr...

Ldo quality rails this time made in 440c stainless steel which makes them last much longer and avoid rust. These are absolutely the best rails LDO ...

**Preorder item, ships in about 30-45 days or less**Bent Sheet metal V0.1 bed holder for a more rigid bed 

In stock! **350 mm ships in 15-20days**for Trident and V2.4Set of 3 backers 

Fused power inlet for V0.1 **Does not come with fuse**Standard: IEC 60320 C14Rating: 15A 250V AC / 10A 250V ACInsulation Resistance: 100MΩ 500V DC ...

Rubber feet for V0.1 comes in a set of 4

F625 2rs Bearings

Original NSK brand 695 bearings with dual-sided rubber sealing (2rs)Sold individually

Compatible with Klipper screen for Voron 2.4 upgrade  This is a 5-inch LCD touch screen with a resolution of 800 x 480 for Raspberry-Pi. The disp...

Full V0.1 motor kit 1 - LDO-36STH17-1004AHG(VRN) 2 - LDO-35STH48-1684AH(VRN) 1 - LDO-42STH25-1004CL200E(VRN)

Full Ldo v2.4 Motor kit1 - LDO-42STH20-1004ASH(VRN) NEMA 17. 1.8° Step Angle. 200 Steps Per Revolution. 1.0 Amp 1.8Kgf cm Holding Torque. 20m...

T nut bar kit for linear rail installation on V0 and V0.1 printers includes 5 bars 

Wet 3D printing filament can cause all sorts of issues. In fact, many of the issues that hotends or nozzles get blamed for can actually be traced b...

Should not be used in place of Boron Nitride Paste. The primary application of MX-4 paste is for coating the top of a Mosquito® Conduction Heat Bre...

At long last, there is an official silicone boot for the Mosquito. And yes, it is a boot, not a sock. Socks can be flimsy, fall off, and tear easil...

multi purpose 6mil thickness for improved durability and protection nitrile and powder free single use available in 3 sizes **Larger quantities a...

All metal heat break upgrade for Biqu H2 extruder and biqu BX printers, this will allow printing at higher temps. Stainless: BX all-metal throat,...

Spring Steel sheet measuring .5 mm thickness  Sabic Ultem (PEI) 1000 is used for the smooth side for its superior ability to handle heat cycles...

NEMA 17 1.8° Step Angle. 200 Steps Per Revolution. 1A Phase. 26mm Body. 200mm 8*8 Output Shaft with nut

**Preorders Now open for batch 2.5!!** batch 2 sold out and on its way to us batch 1 Complete **our units will be shipped via Air directly from LD...

Printed using state of the art cf-ppa "htn nylon" on an Intamsys Funmat HT  Heat Deflection Temp (HDT) of 220°C [Greater than either Ultem™ 9085 o...

1. The hotend’s core parts are mainly composed of copper alloy, which has the advantage of better heat conduction. 2. high temperature resistance ...

inn the process of 3D printing, PEEK, PEKK, PEI, PSU, PPSU, and other filaments that can be melted above 300℃ are called high-temperature filaments...

Updated mainboard with silent TMC2208 stepper drivers:  Compared to the Ender 3 and Ender 3 Pro a V2 design that delivers users out-of-the-box ex...

LDO 36mm stepper for Voron V0.1 Afterburner  LDO-36sth17-1004ahfor Galileo and Orbiter extruder 1.8° Step Angle. 200 Steps Per Revolution. 1A Phas...

1. The hotend’s core parts are mainly composed of copper alloy, which has the advantage of better heat conduction. 2. high temperature resistance ...

MGN7H Linear Rail with Carriage  440c stainless steel rails for improved longetivity LDO quality rails Set includes 5 rails for a complete v0 build

Product Description: Would you like an indestructible nozzle? Try ours out. With a 64 Rockwell C hardness (Vickers HV 910) minimum rating and the h...

Made out of polysulfone (see video) will act as an insulator between bed heater and frame to keep the heat on the bed  **set of 4 per order**

Spring Steel sheet measuring .5 mm thickness  Sabic Ultem (PEI) 1000 is used for the smooth side for its superior ability to handle heat cycles...

Printed using state of the art cf-ppa "htn nylon" on an Intamsys Funmat HT  Heat Deflection Temp (HDT) of 220°C [Greater than either Ultem™ 9085 o...

Made out of polysulfone (see video) will act as an insulator between bed heater and frame to keep the heat on the bed  **set of 4 per order**

used for input shaper in klipper The ADXL345 is 3-axis accelerometer with high resolution  measurement at up to +/-16 g. Digital output data is  a...

In stock! **350 mm ships in 15-20days**for Trident and V2.4Set of 3 backers 

Endstop pcb for x and y available in both mechanical and hall effect versions. requires printed parts located here 

60w 24v heater standard size fits most creality blocks and other Standard and Heavy Duty can achieve temperatures over 350C in a very short time. ...